Soil Ph Sensor Arduino

Soil Ph Sensor Arduino We aim to show you accurate product information. Manufacturers, suppliers and others provide what you see here, and we have not verified it. Great Sensors for Smart Car Arduino Project. Having Fun With Electronics and Programming.

  • PH0-14 Value Detect Sensor Module + PH Electrode Probe BNC Compatible for Arduino.Suitable for wide range of application: Aquariums, Hydroponics, Laboratory etc. The PH electrode probe is accurate and reliable that can gives almost instantaneous readings;PH range: 0-14 PH;Temperature range: 0-80℃;Zero-point: 7 ± 0.25PH;Internal Resistance: ≦250MΩ.
  • Detectable concentration range: PH0-14; Response time:≤5S; Settling Time:≤60S; Component Power:≤0.5W. Value Detect Sensor Module With 4pcs M3 Mounting Holes. Module Size: 42mm×32mm×20mm; Output: Analog voltage signal output.
  • Arduino PH Sensor Module,PH Value Detection Detect Sensor Module Monitoring Control for Arduino BNC Electrode Probe,working temperature:-10~50 ℃ (nominal temperature 20 ℃);Humidity: 95% RH (nominal humidity 65% RH).
  • The PH electrode BNC has a single cylinder that allows direct connection to the input terminal of a PH meter, controller, or any PH device which has a BNC input terminal. The PH electrode probe is accurate and reliable that can gives almost instantaneous readings.
  • Package Includes: 1pcs Liquid PH0-14 Value Detect Test Sensor Module and 1pcs PH Electrode Probe Hydroponic Sensor BNC Interface. 180 Days Warranty. Feel free to contact us if you have any problems.

Features:


Soil moisture module is most sensitive to the ambient humidity.It is generally used to detect the moisture content of the soil.
When humidity does not reach the threshold value, the module DO port output high lever; when the humidity exceeds the set threshold, the D0 output low lever.

  • Pin: Analog signal output, GND, VCC
  • Operating voltage: 3.3- 5.5 VDC, Output voltage: 0-3 VDC
  • Interface: PH2.54-3P, Size: 98 x 23mm (LxW)
  • This capacitive soil moisture sensor distinguishes most of the resistive sensors on the market and uses capacitive sensing to detect soil moisture. It is made of corrosion resistant material which gives it an excellent service life.
  • Built-in voltage regulator chip, support 3.3-5.5V DC, can be used for your Arduino and Raspberry Pi project. Applications: Garden plants ,Moisture detection ,Intelligent agriculture

Specification:

PH0-14 Value Detect Sensor Module + PH Electrode Probe BNC For Arduino, Suitable for wide range of application: Aquariums, Hydroponics, Laboratory etc.

Package Includes:

1pcs Liquid PH0-14 Value Detect Test Sensor Module

1pcs PH Electrode Probe Hydroponic Sensor BNC Interface

Features of PH0-14 Value Detect Sensor Module:

Working current: 5-10mA

Heating voltage: 5 ± 0.2V (AC DC)

Detectable concentration range: PH0-14

Detection Temperature range: 0-80 ℃

Response time:≤5S

Settling Time:≤60S

Component Power:≤0.5W

Working temperature:-10-50 ℃ (nominal temperature 20 ℃)

Humidity: 95% RH (nominal humidity 65% RH)

Module Size: 42mm × 32mm × 20mm

Output: Analog voltage signal output

Features of PH Electrode Probe BNC For Arduino:

PH range: 0-14 PH

Alkali Error: ≤15 mv

Response Time: ≦1min

Zero-point: 7 ± 0.25PH

Temperature range: 0-80℃

Internal Resistance: ≦250MΩ

Operating Temperature: 0-60℃

Theoretical Percentage Slope: ≧98%

Terminal Blocks: BNC plug

Value Detect Sensor Module has 4pcs M3 Mounting Holes; and the PH electrode has a single cylinder that allows direct connection to the input terminal of a PH meter, controller, or any PH device which has a BNC input terminal.

BNC Connector suitable for most PH meter and controller.

The PH electrode probe is accurate and reliable that can gives almost instantaneous readings.

Prices of Soil Ph Sensor Arduino:

$15.88 – $125.44

Sharing is caring!

Leave a Comment

Your email address will not be published.

Translate»
error: Content is protected !!