125 Aquarium Stand: This is a very sturdy aquarium stand that is made from high-quality materials. It has a large capacity for holding your fish tank and will last for many years. The stand is made from aluminum and has a powder-coated finish to protect it from rust and corrosion. The stands come with mounting hardware and instructions for easy installation.

The 125 Aquarium Stand is a great way to display your aquarium. The stand is made of high-quality metal, so it is sturdy and durable. The stand has a raised base with rounded corners, which allows you to see the water from all angles. It also includes an overhang top shelf that can be used for plants or other decorations. This shelf is also made of metal, so it will not rust or corrode over time.

The 125 Aquarium Stand comes in two different finishes: satin black and satin silver/white. Each one looks sleek and modern, so you can match it with any décor in your house! This aquarium stand is great for any freshwater fish tank between 10-20 gallons in size (depending on if the aquarium has a canopy).

Cut all the pieces according to the cutlist.

Using a miter saw, cut all the pieces according to the cutlist. Sand any rough edges where necessary.

Assemble the frame using wood glue and 2½-inch finishing nails. Attach the back panel with ¾-inch staples using a staple gun.

Build the Face Frame

Oops! Click Regenerate Content below to try generating this section again.

Assemble the Base

Step 1: Assemble the Base

Start by creating the base of your stand using the 2x4s and 3⁄4″ plywood pieces as shown in the diagram above. If you have difficulty visualizing this, think of it like a table with a hollowed-out middle section and a solid top, bottom, side and back panel (although the panels are slightly shorter in height than a normal table). Use wood glue and brad nails to attach these together before securing them with pocket hole screws according to the size provided below. Be sure that you clamp each piece before securing it with pocket hole screws for best results (see image below for reference).

Assemble the Sides

  • Fold the side pieces in half lengthwise and mark the center point on each end of the side piece.
  • Measure 1-1/2″ from each end and make a mark at 2-3/4″ from each side of the center lines you made in step 1 (see diagram).
  • Attach the face frame pieces to the sides with glue and 1-1/4″ pocket hole screws (see diagram).

Assemble the Top and Bottom

Oops! Click Regenerate Content below to try generating this section again.

Attach the Top and Bottom to the Sides (Flush with Face Frame)

Attach the top and bottom to the sides (flush with face frame), and attach them together, as in Figure 9. Use glue and screws to make sure that these parts stay together through the bumps of life.

Use a straight edge to ensure that your edges are flush, as shown in Figure 10.

Assemble the Bottom Shelf & Attach Supports

The first step is to cut dados in the bottom shelf pieces. Check the width of your plywood, and set your table saw fence to that distance. Set a dado blade on your table saw, and set it to match the width of the plywood (the wider the better). Set the height at 1″.

Run each piece through your table saw so that you end up with two side pieces with a dado cut in them:

You can use wood glue or nails to attach shelf supports to bottom shelf pieces. If you have a nail gun, this is an easy way to attach these pieces together: run nails along both edges for added strength.

Attach bottom shelf pieces to sides by aligning them flush with the front edge. Use clamps to hold them down while you add screws from inside cabinet sides into bottom shelf boards:

Attach Braces to Sides

With the braces cut to length, you’re ready to attach them. The simplest way is with glue and screws.

  • Set the sides of your stand on top of their corresponding plywood sheet. Make sure they’re oriented correctly (the back should face you). Push them against each other and lightly clamp or tape them together so they don’t shift while you work.
  • Apply a thin layer of glue to the inside edge of one brace, then set it in place on the side panel so that it’s flush with its top edge. Use a torpedo level or carpenter’s square to make sure it’s straight, then drive two screws through each side panel into the end grain of both pieces of wood for a total of four screws per brace.

Cut and Fit Back Shelf, Attach

  • Cut and fit the back shelf (C), making sure to keep the shelf aligned as you cut it to size. Mark the bottom of the aquarium stand on the back and front rails, then trace a line around it onto the back shelf (C). Mark along this line where the top of each stile is, then cut along that line.
  • Apply wood glue to the edges of the back shelf (C) and set them in place between the two sides of your aquarium stand. Align everything so that your marks from Step 3 are visible, then screw through both sides into these marks at all four corners of your aquarium stand using 1-1/4″ screws. If needed, remove excess glue before it dries using a damp rag or sponge.
  • Finish (or not) your aquarium stand as desired for your project and location! Now you need only fill it with water, gravel or rocks and sea creatures!

Assemble and Install Divider

  • Assemble the divider, using glue and 1-1/4″ screws.
  • Install the divider on the bottom shelf, using glue and 1-1/4″ screws.
  • Install the divider on the top shelf, using glue and 1-1/4″ screws.

You built an aquarium stand.

Congratulations! You’ve built an aquarium stand—assuming you followed all the steps in this guide.

If you’re still having trouble, here are some helpful pointers:

  • If you find that your aquarium stand isn’t very sturdy, that may be because you didn’t screw in the screws correctly. Be careful to put them in straight!
  • A lot of people forget that they need nails for their project. Don’t be one of those people!

Maintenance of 125 Aquarium Stand

If you have a freshwater aquarium, it is necessary to add a small amount of salt in the water. This will provide some benefits. For example, it helps in the prevention of diseases and parasites, making your fish much healthier. It also contributes to stress reduction.

Price of 125 Aquarium Stand

If you have your heart set on a one-piece, 125 gallon aquarium stand that holds up to 125 gallons of water, you can expect to pay around $170. The price of a 125 gallon aquarium stand is worth it if you want something heavy duty and are willing to invest in the best quality materials.

Leave a Comment

Your email address will not be published.

error: Content is protected !!